Lucasey LC200C Instalační manuál stáhnout pdf

LC200C Ceiling Mount

for Monitors up to 32" with

up to 200mm VESA Patterns

LC200C Ceiling Flange

LC200C Flange Cover

Countersunk Screws

Lag Screws

1/4-28 x 5/16" Setscrews

1" NPT Outside Pipe

Cord Access Hole

Do Not Adjust

Past the Red Line

Inside Adjustable Pipe

Monitor Attaching Screws

Flat Washers

Monitor Not Included

VESA Plate

Do Not Remove the Safety Cable

Follow the directions provided by the monitor manufacturer

to expose the VESA mounting pattern of threaded inserts on

the back of the monitor. Attach the VESA Plate to the monitor

with Monitor Attaching Screws specified by the monitor

manufacturer. Several screw sizes are provided for

conveinience.

Predetermine the best possible viewing location for the

monitor allowing for tilt and pivot action.

Use the LC200C Ceiling Flange as a template to mark and

drill pilot holes 2-1/3" deep into the wood ceiling joist

using a 1/8" bit for each of the lag screw locations.

Attach the LC200C Ceiling Flange to the ceiling wood joist

using the provided Lag Screws. If mounting into concrete,

metal beams or at an angle, contact Lucasey for ceiling

mount accessories compatible with this mount.

Attach the LC200C Flange Cover to the LC200C Ceiling Flange

using the provided countersunk screws.

Carefully slide the Inside Adjustable Pipe, with attached

monitor, into the Outside Pipe. Adjust to the appropriate

length (Do not adjust past the red line) and tighten the

Setscrews.

If desired, run the monitor cords through the pipes using the

Cord Access Hole at the top and the hole in the bottom of the

Inside Adjustable Pipe.

Screw the Outside Pipe, with attached monitor, into the

LC200C Ceiling Flange.

Double check to make sure all fasteners, including the

adjustable pipe setscrews, are secure and tight.

Hardware List

#14 x 2-1/2" HWH Lag Screws ........................................................... 4

5/16-18 x 1-7/8" Flanged SHC Bolt ...................................................... 1

5/16-18 Nylock Nuts ............................................................................ 1

5/16" Bellville Washers ...................................................................... 2

1/4-20 x 1-1/2" Flanged SHC Bolt ........................................................ 1

1/4-20 Nylock Nuts .............................................................................. 1

1/4" Bellville Washers ......................................................................... 4

1/4-28 x 5/16" Setscrews .................................................................... 2

#10-32 x 3/4" Countersunk Screws .................................................... 2

4mm x 25mm Set Screws ... 6 4mm Hex Nuts ... 12

5mm x 30mm Set Screws ... 6 5mm Hex Nuts ... 12

6mm x 30mm Set Screws ... 6 6mm Hex Nuts ... 12

4mm x 12mm Phillips Screws ... 6 5mm Flat Washers ... 36

5mm x 12mm Phillips Screws ... 6 1/4" Flat Washers ... 18

6mm x 12mm Phillips Screws ... 6

INSTALLATION INSTRUCTIONS

Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1

LC200C Ceiling Mount 1

Shrnutí obsahu

Strany 1 - LC200C Ceiling Mount

LC200C Ceiling Mountfor Monitors up to 32" withup to 200mm VESA PatternsLC200C Ceiling FlangeLC200C Flange CoverCountersunk ScrewsLag Screws1/4-2

Komentáře k této Příručce

Žádné komentáře

Lucasey LC200C Instalační manuál

Procházejte online nebo si stáhněte Instalační manuál pro Stropní držáky pro ploché obrazovky Lucasey LC200C. Lucasey LC200C flat panel ceiling mount Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce